Elastomer Material Types A-Z
ACM elastomers offer excellent heat resistance; they can typically be used at temperatures of 150°C (up to 175°C for limited periods). They provide high resistance to oxygen, ozone and industrial oils. Resistance to water is generally poor, and compression set and low temperature flexibility depend on base polymer and compounding choice. ACM elastomers are used primarily used where combined resistance to heat and oils is required.
AEM rubber materials offer an unusual combination of physical properties; high heat resistance (up to 175°C), excellent ozone and weather resistance, moderate resistance to mineral oils, low temperature flexibility to –30°C, good resistance to hot water and high tensile strength. AEM applications are similar to ACM elastomers, but with an advantage where low temperature flexibility is concerned. They are typically moulded into O-rings seals, boots and ignition wire jackets.
AU / EU
These elastomers generally show outstanding tensile strength, tear and abrasion resistance, and give excellent protection against oxygen and ozone (except in hot climates, due to greater risk of microbiological attack in AU types, and ultraviolet light in the case of EU types. EU elastomers have a better low temperature flexibility (-35°C typically) and both have excellent resistance to high-energy radiation (106 Rads).
Polyurethane rubbers are used where high abrasion resistance and oil / solvent resistance are required together, e.g. hydraulic seals and gaskets, diaphragms, hoses and roller-skate and skateboard wheels. In all applications, consideration should be given to hydrolysis and limited heat resistance.
CR seal materials typically display good resistance to ozone, heat aging and chemicals. Good resistance to refrigerants, aliphatic hydrocarbons, mineral oils and greases. Typical trade name: Neoprene™ (DuPont)
Chlorobutadiene rubbers contain chlorine in the polymer to reduce the reactivity to many oxidising agents, as well as to oil and flame. CR elastomers also have good resistance to ozone cracking, heat ageing and chemical attack. Some of the important applications of CR elastomers include Vee-belts, coated fabrics, cable jackets, tyre-sidewalls, seals and gaskets in contact with refrigerants, mild chemicals and atmospheric ozone.
CSM grades contain 24-43% chlorine content to provide excellent ozone and weather resistance, discoloration by sun and ultraviolet light, high resistance to many oxidising and corrosive chemicals, good resistance to dry heat to 150°C, low flammability and gas permeability, and also good resistance to hot water (when cured with lead oxide).
The low temperature properties are generally limited, depending on the chlorine content of the CSM grade used, and the compression set is not very good. CSM elastomers are generally useful in electrical applications, weather resistant membranes, hoses and acid resistant tank linings.
ECO elastomers are generally resistant to high temperatures, oils, ozone and flame, with gas resistance comparable to NBRs. The temperature range for continuous use is –40 to +120°C, but are generally unsuitable for rubber to metal bonding (they are corrosive to metals). ECO elastomers are suitable for use in seals, gaskets, diaphragms, cable jackets, belting etc, for a wide range of media. However, they are unsuitable for use with ketones and esters, alcohols, phosphate ester hydraulic fluids, sour gas, water and steam.
EPDM elastomers have a fair tensile strength and excellent resistance to weathering, ozone and chemical attack. They also exhibit excellent electrical insulation properties. Peroxide cured elastomers exhibit excellent heat ageing, and resistance to compression set from –40 to +150°C, more so if sulphur cured. They are resistant to a wide range of media, including hot water and steam to 200°C (in the absence of air), but are not considered compatible with mineral and synthetic lubricants, and hydrocarbon fuels. They are typically used in the production of window and door seals, wire and cable insulations, waterproofing sheets and hoses, and seals, O-rings and gaskets.
This is the most chemically resistant elastomer available and is effectively a rubber form of PTFE. It displays other properties which prove most valuable in applications where purity, high temperatures and retention of sealing force are paramount.
FKM seal materials demonstrate outstanding resistance to heat, weather, ozone, oxygen and oxidisers, with very low gas permeability. PPE’s FKM seal materials include copolymer, terpolymer and tetrapolymer grades and bisphenol and peroxide cure systems.
FKM elastomers are highly fluorinated polymers containing few compounding ingredients. They are stable at very high temperatures (they can withstand 200°C / 400°F indefinitely, in service). By comparison, conventional elastomers would become brittle in 24 hours at this temperature, in air. FKM vulcanisates, in general, have outstanding resistance to oxygen, ozone, weather, flame and oxidative chemicals, and excellent resistance to swelling in a wide variety of media. However, they are not compatible with polar solvents (e.g. M.E.K.), some organic acids (e.g. Formic acid), certain methanol and ester based hydraulic fluids (e.g. Skydrol), ammonia and some amines. They are suitable in high-energy radiation environments up to about 106 Rads. Special grades of FKM may be required for use in hot water and steam applications.
FKM elastomers provide high compression set resistance if compounded with bisphenol cure systems. Generally they are serviceable down to –30°C, but specialist grades (such as Endura® V91A) can provide effective sealing down to –45°C. Electrical insulation properties are not particularly outstanding, but would be adequate for sheathing where elevated temperatures, ozone, chemical and flame resistance are required (e.g. shaft seals, O-rings and gaskets, diaphragms and cable sheathing).
FVMQ elastomers are modified silicone rubbers, with superior fluid resistance, but limited to about 175°C (347°F).
The hydrogenation process of NBR elastomers provides excellent heat and ozone resistance. Peroxide cured HNBRs have the best compression set and heat resistance, and high-nitrile (ACN) HNBR elastomers have better resistance to mineral oils. HNBRs combine best resistance and low temperature flexibility, although they are more expensive than NBRs. HNBRs are useful where resistance is required to ozone and weather, ageing in hot air and industrial lubricants, hot water and steam to 150°C, amine based corrosion inhibitors and sour gas (H2S), and high-energy radiation.
HNBRs fill the gap between NBRs and FKMs in many areas of application where resistance to heat and aggressive media are required simultaneously, and may therefore provide a lower cost alternative to FKM elastomers.
Resistant to the same fluid types as EPDM, the distinctive properties of IIR rubber materials are very low gas and moisture permeability, excellent insulating properties, good ozone and weathering resistance, and resistance to many organic and inorganic media.
IIR elastomer materials can be polymerised with various halogens (e.g. Chlorine / Bromine) to improve resistance to certain chemical media, but at the expense of electrical insulation and moisture resistance. They can be used from –40 to +120°C typically, and are mostly used in the production of tyre inner tubes, seals and gaskets, vacuum seals, membranes and pharmaceutical goods.
NBR (BUNA N)
NBR elastomers are available in five basic grades; based on acrylonitrile content, giving proportional physical and chemical properties. NBRs typically have (depending on increased ACN content), decreasing low temperature flexibility, increasing compression set, gas permeability, improved heat ageing and ozone resistance, improved tensile and abrasion strength, hardness and density. NBRs are used where good resistance is required, to aromatic hydrocarbons at –40 to +120°C (e.g. gaskets and seals, hoses and cable jacketing), typically in the oil and gas industry.
- High Nitrile: >45% ACN content
- Medium Nitrile: 30-45% ACN content
- Low Nitrile: <30% ACN content
The higher the ACN content, the higher the resistance to aromatic hydrocarbons.
The lower the ACN content, the better the low temperature flexibility.
The best overall balance for most applications is medium ACN content.
Natural rubber (tapped from the cultivated rubber tree) exhibits high tensile strength, abrasion resistance, resilience, tear strength and low hysteresis.
The chemically similar polyisoprene has lower strength properties than the natural form but better low-temperature properties. Both rubbers are susceptible to degradation by weathering characteristics, and both show poor resistance to mineral and petroleum-based oils and fuels. Typical long-term operating range is from -50°C to 70°C, with the main applications being tyres, vibration mounts, springs and bearings.
Produced as a substitute for NR (Natural Rubber); in general, SBRs can be used in similar applications as NR / IR elastomers, except in severe dynamic applications (e.g. requiring low heat build-up on flexing). SBRs can be used in tread compounds on car tyres, but not truck tyres. SBRs have inferior weathering and chemical resistance to most other elastomers.
TFE/P (also known as FEPM)
The base polymer is solely produced by the Asahi Glass company, and sold under the name ‘Aflas’. TFE/P vulcanisates exhibit similar thermal stability to FKM elastomers, but better electrical resistance and a different chemical resistance profile (e.g. sour gas, acids and alkalis, ozone and weather, steam and water, all hydraulic and brake fluids, alcohols and high energy radiation). However, they are not compatible to aromatic hydrocarbons, chlorinated hydrocarbons (e.g. M.E.K. and acetone), organic acetates and organic refrigerants.
FKM elastomers exhibit better compression set. The low temperature flexibility is relatively poor (except in certain fluids that would plasticise the rubber to some extent). It is always recommended to carry out functional tests under working conditions. TFE/P elastomers are finding wide application; mainly in oil-field operations and chemical processing as O-rings, seals and gaskets, cable insulating, jacketing and hose liners.
The distinctive properties of silicone rubbers are outstanding resistance to ozone and corona, outdoor weather and sunlight. Special compounds will withstand up to 300°C; however, in the absence of air, silicones can revert to a paste, even at lower temperatures. The usual high temperature limit, quoted for continuous service, is 200°C. Silicones have an excellent reputation for their low temperature flexibility (some compounds to –90°C) and electrical insulation, which are maintained fairly constant at the full range of service temperatures. Electrically conductive compounds are also available.
Silicones have a low level of combustible components; even when exposed to flame, the elastomer is reduced to a non-conducting silica ash. Silicones also exhibit excellent compression set and high physiological inertness (tasteless, odourless and completely non-toxic).
Silicones are also resistant to bacteria, fungi, high energy radiation (to 106 Rads) and excellent release properties (except to glass). The main limitations are low tensile properties and poor resistance to acids, alkalis and steam above 120°C. Silicone elastomeric parts are used for electrical insulation, gaskets and O-rings (static or low dynamic applications only), food and pharmaceutical goods.
Further information quick links: